Custom Garage Flood Protection
Protect vehicles, tools and connected living space with a custom garage door flood barrier designed for rising water. Heavy-duty aluminum panels deploy when needed, then remove to restore normal vehicle access.
Custom systems from
per sq. yd. Final cost depends on size and installation.
Heavier construction
Than standard lightweight flood panels
Verified rating
Based on current product reviews
Current listed warranty
See the applicable warranty terms
Stated U.S. installations
Homes and commercial projects
An aluminum flood barrier for a garage door is a removable stop-log system custom-sized to the opening. Aluminum panels slide into side channels and compress against EPDM seals to form a structural barrier against rising water. After the flood risk passes, the panels are removed so the garage returns to normal use.
A rubber threshold can help with minor rain or runoff. It does not create the structural wall needed when floodwater rises and pressure builds against your garage.
Vehicles, electrical tools, storage, HVAC equipment and interior walls can all be exposed through the garage.
Stacked aluminum stop logs form a rigid wall instead of relying on a low flexible strip.
Panels are removable, reusable and stored separately until severe weather is forecast.
The removable planks are stored when the opening is used normally. Before a flood event, they are inserted into the permanent posts and locked against the sealing surfaces.
Send the clear width, target height, installation surface details and photos for a preliminary configuration review.
The permanent components are installed once. Initial installation is typically about 1–2 hours, depending on the site
Insert the removable planks, engage the internal compression system, then remove, clean and store them after the risk has passed.
Waterproof performance depends on the complete system: aluminum rigidity, side-post geometry, seal material and consistent compression—not simply the appearance of the front panel.
01 / SIDE POSTS
No exposed front screws through the sealing face. The cleaner design reduces potential water-entry points and can be recessed into the wall.
02 / STRUCTURE
Made without recycled aluminum and engineered at approximately 2.5 times the weight of standard lightweight panels for greater rigidity.
03 / WATERPROOFING
Interlocking EPDM sealing ridges expand contact area, distribute compression and provide backup sealing if one ridge is worn.
04 / DURABILITY
High-elasticity, weather-resistant rubber is selected to maintain recovery and flexibility through repeated use and outdoor exposure.
The published report describes a commissioned performance test for the DSC-095 series under defined flow, wave and static-water conditions.
Sample test
PAS 1188-4 reference
Report issued 2024
| Test | Condition | Reported Result |
|---|---|---|
| Flow | 0.85 m water depth, 30 min | 0.27 L/h/m leakage; 0.53 mm deformation |
| Wave | 1.10 m water depth, 15 min | 0.56 L/h/m leakage; 0.62 mm deformation |
| Static | 1.50 m water depth, 60 h | 0.51 L/h/m leakage; 0.46 mm deformation |
Scope note: these are results for the tested sample under defined conditions. They are not a guarantee for every opening or for an entire building. Final height and performance require configuration and site review.
Real projects show more than a product rendering. They reveal how the same removable stop-log system is adapted to different widths, door frames, mounting surfaces and daily-access requirements.
Custom removable aluminum flood barrier supplied for a garage opening exposed to floodwater risk.
Installed once. Ready before the water rises.
Provide aluminum flood barriers at the entrance of the underground parking lot
Installed once. Ready before the water rises.
Custom aluminum flood barriers for a two-lane underground garage entrance in San Gabriel, California.
Installed once. Ready before the water rises.
Removable aluminum flood barriers installed for an underground parking entrance in Clearwater, FL.
Installed once. Ready before the water rises.
Custom garage barriers are produced in-house, from aluminum processing and cutting through electrophoresis anti-corrosion treatment, assembly, inspection, packing and factory-direct dispatch.
Manufacturing Since 2022
Sets / year stated capacity
Custom production where applicable
Current listed product warranty
*Production timing depends on order quantity and specifications. Certification and test documentation should be requested and reviewed for the applicable product and project.
The listed Eudore Series II configuration uses 100% new 6063-T5 aluminum rather than unspecified recycled material.
Dual gear-profile EPDM seals, panel compression and the hidden-fixing side post are shown and explained with real component images.
Width, target flood height, wall, floor, door hardware and mounting position are reviewed before the final configuration.
Center-post requirements and installation method depend on width, height and site conditions; they are not decided by one marketing number.
Important performance disclosure: Water resistance depends on the approved configuration, mounting surface, wall and floor condition, installation, compression and seal maintenance. Final project conditions must be confirmed before production.
Both may be sold as “garage flood protection,” but they address very different water conditions.
| Protection Factor | Eudore Aluminum Barrier | Rubber Threshold Kit |
|---|---|---|
| Designed for | Rising floodwater | Minor rain, splash and runoff |
| Protection height | Custom, modular height | Usually only a few centimeters |
| Structural water pressure | Engineered barrier system | Minimal resistance |
| Removable after a storm | Yes | Usually remains on the floor |
| Custom fit to opening | Width, height and mounting | Trim-to-length strip |
| Best choice for flood-prone areas | Yes | No |
This system is intended for meaningful rising-water risk. It is not always the correct solution for a small amount of wind-driven rain or a drainage problem that should be repaired first.
Send the clear opening width, required protection height and a straight-on photo. Our team reviews the mounting surface, door hardware and panel span before recommending a configuration.
Often provides strong wall backing and preserves more of the clear opening.
Can create a cleaner, integrated appearance when the wall and door geometry allow it.
Keeps the driving surface smooth and reduces raised-threshold and tire interference.
Engineering note: Center-post requirements depend on opening width, barrier height and project conditions. Some garage-optimized configurations can span up to 5 m without a center post; final selection must be confirmed for your opening.
★★★★★
Based on 5 current product reviews
These comments are tied to the current Eudore aluminum flood barrier product listing.
Verified ownerThis is one of the best solutions on the market right now to protect your property against flood water !
Verified ownerWell made product. Overall I’m very satisfied. 4* not 5* because a few details lacking (from shipping issues, minor damage to missing clamps) but I got it all sorted and pleased with end result.
I additionally had custom aluminum shrouds made locally to cover the edges and exposed lag bolts.
I spent $3,800. Very fair value for what you get.
Overall satisfied and would highly recommend. Solid A
Verified ownerVery professional and knowledgeable company. The product is very high quality and well built and functional. Very easy to install. Highly recommended! Thank you!
Verified ownerGreat product!
Review wording and status checked against the current product review section.
Preliminary measurements and clear photos are enough to start. We review the barrier width, protection height, mounting method, floor condition and center-post requirement.
Current product pricing; custom options affect the final quote.
You do not need final drawings. Photos help us identify mounting and door-hardware issues before recommending a configuration.
We use your measurements and photos only to evaluate this project. No obligation to purchase.
Every garage is different. These answers cover the most common starting points.
The aluminum panels are removed when flood protection is not needed. Only the selected mounting components remain, and a recessed floor-channel option can help preserve a flat driving surface.
Prepared garage configurations are designed for fast, tool-free panel deployment. Actual time depends on opening width, panel count, storage location and user familiarity, so practice before storm season.
Provide the clear opening width, desired flood-protection height, and straight-on photos showing the door frame, nearby walls, floor and any hinges or hardware.
Depending on the wall, side posts may be recessed for a flush appearance or installed with removable anchoring. A recessed inside installation typically requires about 55 mm of depth.
The need for a center post depends on width, protection height, expected load and system configuration. Some optimized systems can span up to 5 m without one, subject to engineering confirmation.
Performance depends on the approved barrier configuration, mounting surface, wall and floor condition, installation quality, seal compression and maintenance.
No. Threshold seals are intended mainly for light runoff and wind-driven rain. This modular aluminum system is designed for rising floodwater.
Send one front-view photo, your garage opening width and the water height you want to block. We will prepare a custom recommendation before you order.
